ABSTRACT Industry and universities around the world invest time and money to develop digital computer programs to predict gas turbine performance. This study aims to demonstrate a brand new digital model developed with the ability to simulate gas turbine real time high fidelity performance. The model herein described run faster than 30ms per point, which is compatible with a high-definition video refresh rate: 30 frames per second. This user-friendly model, built in Visual Basic in modular structure, can be easily configured to simulate almost all the existing gas turbine architectures (single, 2 or 3 shaft engines mixed or unmixed flows). In addition, its real time capability enables simulations with the pilot in the loop at earlier design phases when their feedback may lead to design changes for improvements or corrections. In this paper, besides the model description, it is presented the model run time capability as well as a comparison of the simulated performance with a commercial gas turbine tool for single, 2 and 3 shaft engine architecture.

ABSTRACT Power plants operating in combined cycle present higher thermal efficiency (over 60%) and increased power generation when compared to traditional simple cycles, such as gas or steam turbines operating alone. Considering that the power plant evaluated in this paper is already operational, a further development concerning to the power plant control system is required in order to evaluate disturbances and frequency variations, generated by the electrical grid during normal operation, as the loads applied to the turbines are intrinsically associated to the grid frequency. A computer program able to simulate the control system was developed to cope with these instabilities and to guarantee the necessary protection to the power plant operation. The develop program was made using MATLAB Simulink®. The main components of the power plant consists of 2 gas turbines of 90 MW each and a steam turbine of 320 MW, totalizing 500 MW. Firstly, the power plant main components were constructed separately. Once obtained stable models, the exhaust from the gas turbine was connected to the water-steam cycle through the heat recovery steam generator. The main parameters necessary to adjust the model such as gains, limits and constants were obtained from the power plant operational data. The simulation results allowed the evaluation of some key parameters; others are possible but not shown, such as power, exhaust gas temperature, fuel flow and variable stator angles during grid instabilities. The studies were conducted by testing the robustness, response time, transient analysis, steady state analysis and reliability of the proposed model.

ABSTRACT: Design and development of gas turbine components are a complex multidisciplinary process. At the beginning of the power class definition and engine configuration it is necessary to conduct a market study. The results obtained are used in gas turbine thermodynamic cycle calculations and analysis in order to define the gas turbine design point. Several possible design points are evaluated during this procedure. After this step, the gas turbine components are designed, including: compressor, combustion chamber and turbine. For industrial gas turbine purposes, it is common to use a free turbine after the gas generator, also commonly named power turbine. In this work, a power turbine was initially designed by meanline techniques, considering internal loss mechanisms, to obtain the main dimensions. The geometries of the components were generated in a 3-D environment to make possible the mesh generation, process to discretize the physical domain into a computational domain and use a 3-D Computational Fluid Dynamics tool. The results from the meanline approach and from the 3-D turbulent flow numerical simulations were compared to verify the turbine operational conditions and its predictions at design and off-design conditions. The gas turbine under study is a project, derived from a low thrust turbojet previously developed by Instituto de Aeronáutica e Espaço. The power turbine project uses the same turbojet gas generator, already designed and currently under tests.

ABSTRACT: The Instituto Tecnológico de Aeronáutica (ITA) is an Engineering school maintained by the Air Force Command, Ministry of Defense. The aim of the Turbomachines Department at ITA is the human resources training for design and development of aeronautical and industrial gas turbines, necessary for the Gas Turbine Program of the Departamento de Ciência e Tecnologia Aeroespacial (DCTA). The human resources training is carried out in undergraduate and graduate courses at ITA, where topics in gas turbine and turbomachinery are taught. The gas turbine topic is taught in the undergraduate degree, in Mechanical-Aeronautical Engineering course, and focuses on gas turbines' performance for different configurations (turboshaft, turbojet and turbofan). Lecture notes containing the essential elements of the course are made available for the students, addressing the basic theory of the gas turbines required for the performance study at the design and off-design point. The technological aspects are presented and discussed during detailed studies of the actual cycle. Simple gas turbines and more sophisticated ones are studied, for both aeronautical and industrial application. Performance calculations at design and off-design point of the main engine's components and the cycle are done manually, encouraging students to develop spreadsheets. The theory is complemented with laboratory classes and technical visits, when the practicalities involving gas turbines operation and tests are presented to the students. As an activity laboratory class, the students perform disassembly-assembly of a small industrial gas turbine.